Start with the lens you actually own
High index lenses are thinner and lighter than standard lenses, which is why they suit stronger prescriptions. The same features that make them comfortable also mean the surface deserves a little respect. Valley Eyewear's High Index Clear Prescription Blue Blocker Lenses are recommended for prescriptions with a SPH value of +/- 4.00 or greater, and they carry scratch-resistant and anti-reflective coatings. Those coatings are your allies against glare and everyday wear, but they are not a licence to scrub.
Blue blocker lenses add a filter for digital screen light, but the cleaning routine is the same as for any quality prescription lens: remove grit first, use a safe cloth, and store them properly. The steps below work for this lens and are a sensible baseline for high index lens care in general.
A safe daily cleaning routine
Follow these steps in order. Each one removes a different kind of risk, from abrasive dust to oil smudges.
- Rinse before you wipe: Hold the lenses under a gentle stream of lukewarm water to float away dust and grit. Wiping a dry lens is the most common way to create fine scratches, especially on high index surfaces.
- Use a lens-safe cleaner: Apply a small amount of lens cleaner or a drop of mild soap to your fingertips and gently rub both sides of each lens. Avoid household glass cleaners, alcohol-heavy sprays, or anything with ammonia, as these can degrade anti-reflective coatings over time.
- Rinse again and shake off excess: Rinse thoroughly so no soap residue remains. A film of residue attracts dust and makes the next cleaning harder. Shake the frame gently rather than flicking it.
- Dry with a clean microfibre cloth: Use a clean, dry microfibre cloth made for eyewear. Paper towels, tissues, and clothing fibres can contain wood or synthetic particles that abrade the surface. Wipe in a smooth motion rather than circular scrubbing.
- Check the edges and bridge: Grime often collects where the lens meets the frame. A soft brush or the corner of a microfibre cloth can lift it without pressing hard on the lens centre.
Why anti-reflective coatings need gentler handling
Anti-reflective coatings are applied in thin layers. They reduce glare and improve clarity, but they are softer than the lens material underneath. That is why the usual advice to 'just wipe them on your shirt' is a bad habit. Over time, abrasive wiping leaves a haze of micro-scratches that no cleaning can reverse.
The High Index Clear Prescription Blue Blocker Lenses also have a scratch-resistant coating. Think of it as a first line of defence, not an invisible shield. Keeping grit off the lens and using a clean cloth is what actually preserves the coating.
Coatings on this lens
- High Index Clear Prescription Blue Blocker Lenses: Scratch resistant and anti-reflective These coatings reduce glare and resist everyday wear, but they still need grit-free cleaning to stay effective.

High Index Clear Prescription Blue Blocker Lenses - High Index Clear Prescription Blue Blocker Lenses: Recommended for prescriptions with a SPH value +/- 4.00 or greater If your prescription falls in this range, the thinner, lighter build is the reason careful handling matters—less material means less room for error when cleaning.
Habits that prevent scratches
Most lens damage happens between cleanings, not during them. These small habits make the biggest difference.
- Store in a hard case: When you are not wearing them, put the glasses in a hard case. A soft pouch protects against dust but not against pressure or impact.
- Never leave them lens-down: Resting glasses face down on a table is a direct route to scratches on the lens centre. Set them down temples-first or put them away.
- Keep a spare microfibre cloth: Carry a clean cloth in your case and wash it regularly. A cloth that has been sitting in a bag collects grit that then gets rubbed into the lens.
- Avoid heat and harsh chemicals: Do not leave glasses on a dashboard or near a heater. Heat can warp frames and stress coatings. Keep them away from sunscreen, hairspray, and cleaning sprays not intended for lenses.
What to do when you are not sure
If a smudge will not lift with the routine above, do not press harder. Re-rinse and try again with a clean cloth. If a mark remains after two gentle attempts, it may be under the coating or a sign of damage. In that case, contact your optical professional rather than experimenting with polishes or abrasive pastes, which can make the problem worse.
The supplied product information does not include a specific cleaning solution recommendation or warranty details, so treat any cleaner you use as a general lens product and check its label for compatibility with anti-reflective coatings.


